Autoclave SSR-3A-PB Use and Operation [EQUIP 1.0]

Download PDFPrint

Training Certificate/Annual Review Form

I. PRINCIPLE

Steam or “moist heat” is the most effective and practical sterilizing agent in general use today. It is inexpensive, nontoxic and very reliable.

The SSR-3A-PB is an electric steam heated gravity air removal sterilizer designed for the sterilization of hard goods and liquids in vented (open) containers. This sterilizer is equipped with one sterilization cycle and three exhaust cycles which can be programmed to suit the requirements of the load to be sterilized.

II. SCOPE

This policy includes general use and operation of the SSR-3A-BP steam sterilizer, and applies to all students and staff at the University of Wisconsin-Milwaukee that utilize the SSR-3A-PB autoclave. If processing biohazardous waste for disposal, procedure Biohazardous Waste Disposal [SAFE 2.0] must be followed.

This autoclave is primarily used for processing and disposal of biohazardous waste, and should only be used for autoclaving of course or research materials if second autoclave (SSR-3A-PB) is not in service. In cases when sterilizer is utilized for anything other than disposal of waste, the time used must be recorded on Consolidated Sterilizer Log and Sterilizer Temperature Recording Disk.

III. EQUIPMENT

Consolidated SSR-3A-PB Electrically Heated Steam Sterilizer

IV. TRAINING

All staff and students that expect to operate this equipment must review this procedure, complete training by Lab Manager or PI, and fill out SSR-3A-PB Training Certificate/Annual Review Form, with a submission type of “Initial Training Certification”.  After initial training, procedure must be reviewed annually and documented with the Training Certificate/Annual Review Form, submission type “Annual Procedure Review”.

V. PROCEDURE

NOTE: The operator must wear protective clothing, including face shield, thermal gloves, high heat vest, and proper lab attire when loading and unloading the chamber. Some materials, especially fluids, if not handled properly, may cause severe burns to exposed skin.

Equip 1.0 Table 1

A. CYCLE SELECTION

a. FAST sterilization cycle

i. The FAST cycle is intended for sterilization of unwrapped goods, glassware, metal, tubing, magnetic stir bars, spatulas, or other porous material.
ii. The FAST cycle should never be used for any fluids, liquid, or biohazardous material. Liquids sterilized with the FAST cycle will boil over due to the fast exhaust rate, which can lead to loss of liquid and damage to sterilizer.
iii. Recommended sterilization time for FAST cycle is 30 minutes.

b. DRY sterilization cycle

i. The DRY cycle is intended for use with wrapped goods (instruments, etc.), pipette tips, empty bottles, empty tubes, and pasture pipettes.
ii. The DRY cycle should never be used for any fluids, liquid, or biohazardous material. Liquids sterilized with the DRY cycle will boil over due to the fast exhaust rate, which can lead to loss of liquid and damage to the sterilizer.
iii. Recommended sterilization time for DRY cycle is 30 minutes with 20 minute dry time.

c. FLUID sterilization cycle

i. The FLUID cycle is intended for use with all fluids and liquids. The FLUID cycle is designed to have a slower exhaust rate, which will allow for cooling of the liquids and help minimize loss due to boilover.
ii. Fluid sterilization time is determined based on the fluid volume of the largest container, as larger volumes will take longer to heat and properly sterilize.

1. Container volumes should be minimized so that cycle times remain manageable.

iii. Recommended sterilization times can be found in TABLE 2. Table 2 is provided as a guide only. Please refer to the specific material’s procedure or package insert for manufacturer’s recommendations about the best temperature and time for sterilization.

Equip 1.0 Table 2

B. OPERATION OF AUTOCLAVE

a. HOW TO RUN A CYCLE

i. Turn on the autoclave generator. A white power switch is located on the front lower right of the autoclave and will glow red when activated.

ii. Turn on exhaust fan. Switch is located on the wall opposite of the autoclave.

iii. Wait approximately 30 minutes to reach full jacket pressure (18±4 psi). Jacket pressure gauge is located on front lower left of the autoclave.

iv. Wearing heat resistant gloves, face shield, high heat vest, and appropriate lab attire, load items into sterilizer. All items must be contained in autoclave buckets or pans to reduce spillage and damage to the autoclave.

NOTE: IT IS CRITICAL THAT ALL CAPS ARE LOOSE TO AVOID EXPLOSION OF TUBES AND BOTTLES IN AUTOCLAVE. BAGS SHOULD BE CLOSED USING A TWIST TIE AND NEVER TIED TIGHTLY. ALL ITEMS MUST ALSO BE PLACED IN BINS AND PANS WITHOUT OVERFILLING TO AVOID SPILLING OF CONTENTS.
FAILURE TO FOLLOW THESE INSTRUCTIONS MAY LEAD TO SERIOUS INJURY AND/OR DAMAGE TO THE AUTOCLAVE.

v. Close the door to the sterilizer and turn the wheel clockwise to tighten.

vi. Set temperature recording disk to record immediately after previous run. Label run with date, run number and initials. If recording disk is full, follow instructions on setting and changing recording disk located in section E.

vii. Choose appropriate exhaust cycle and press red ON/OFF button to begin cycle.

 

b. HOW TO REMOVE A LOAD

viii. Upon completion of a cycle, the chamber pressure will drop to ≤ 2 psi. At this point, press red ON/OFF button to end cycle.

ix. Turn the wheel counter clockwise and open door slowly, being careful not to get hot steam near face or unprotected skin (face shields are available upon request for use when opening hot autoclave). Allow autoclave to cool for 10 minutes prior to unloading.

x. Wearing heat resistant gloves remove the load and allow to cool completely.

xi. If running multiple cycles in succession, steps (i-iii) only have to be performed for the first cycle. Steps (iv-x) must be performed for all cycles.

xii. When all cycles are complete, turn off autoclave generator by pressing the white power switch on the front lower right of the sterilizer. Be careful to avoid the pressurized steam that is released when unit is turned off (Steam is released into an exhaust pipe located on the side of the autoclave).

C. WEEKLY MAINTENANCE

a. Make sure autoclave is off and totally cool.

b. Remove the stainless steel mesh screen from the front drain hole in the bottom of the sterilizer chamber. Lift out and flush under running water.

c. With mesh screen out, pour 1 liter of hot water down drain with a funnel. Repeat this step a total of three times.

d. Wipe inside and outside of autoclave with damp cloth. Sweep around autoclave to pick up any loose debris.

e. Drain the generator once a week right after the sterilizer has been shut down and the water is still hot. This will aid in drawing off all of the sediment and impurities in the water and keep the cleaning process fairly simple and easy.

D. MONTHLY MAINTENANCE

a. Sterilize all buckets used to store biohazardous materials with disinfectant or bleach solution (≥10% bleach is required for adequate sterilization).

b. Remove inner spinning of hub by taking off handles and center ball. After inner spinning has been removed, you will see the small hole for applying oil with an oil can. On newer models a hole is provided on the inner spinning for applying oil, eliminating the need for removing the spinning. After removal of the spinning, proceed by opening the sterilizer door. This will provide access to the eight screws which hold the stainless steel door cover in place. Remove the two screws on each side of the panel and pull away from sterilizer. Turning the hand wheel towards the left will enable you to grease the center pin and back of the locking arms with a grease gun. Grease all friction points of the door leverage such as balls on locking arms and where pins slide through pin retainers.

c. Oil hinge pins.

 

E. OTHER MAINTENANCE

a. Changing and Setting the Temperature Recording Disk

i. Temperature recording disk must be used for all sterilization and test cycles. Temperature display and recording disk is located on the top left of the sterilizer next to the chamber pressure gauge.

ii. Press the black button on the right of the casing to open temperature display door.

iii. Turn the metal knob located in the center of the display disk counter clockwise to loosen. Once loose, this can be pushed to the side to avoid bending the attached arm.

iv. Gently press the top of the needle apparatus (closest to the temperature display) to raise the needle tip off of the paper disk. Never pull needle as this can cause damage to the apparatus.

v. Pull disk off of center peg and place with sterilizer recording log.

vi. Still holding the top of the needle apparatus, insert a new paper disk on to the center peg. The top of the disk should slide in to a slit located just under the temperature display.

vii. Release the needle so it is pressing back in the center of the new disk.

viii. Screw the metal knob back on the center peg and tighten. Be careful not to over tighten knob.

ix. To set for a cycle, turn disk until the needle touches the end of the last run recorded on disk. If disk is unused, it is not necessary to line up the disk. The time displayed on the disk is not used and can be disregarded.

x. Always record the date, run number and initials of operator for each cycle.

xi. Close cover when done.

 

VI. REFERENCES

Operating and Maintenance manual for the Consolidated Model SSR-3A-PB, serial #41285 Electrically Heated Sterilizer

VII. PROCEDCURAL NOTES

A. This procedure is not intended to be used for processing and disposal of infectious or biohazardous waste. If processing waste, procedure [SAFE 2.0] Biohazardous Waste Disposal must be followed.

B. In order to comply with state regulations in regards to disposal of biohazardous waste, the SSR-3A-BP Sterilizer requires a test cycle every 100 hours of use. All sterilization cycles and times are recorded on the Consolidated Sterilizer Log.

VIII. ATTACHMENTS

Autoclave SSR3APB Training Certification Log [EQUIP 1.0.A] PDF

Diagram of SSR3APB

 

Reviewed: 8/9/2016, 8/21/2017, 8/10/2018, 8/6/2019